Open in the explorer

Extended Protection for LDAP Authentication (Domain Controllers only) (DEPRECATED)

Type
Computer
GPO path
Computer Configuration › Policies › Administrative Templates › MS Security Guide
Supported on
Windows Server 2008 and newer
ADMX file
SecGuide.admx
Internal name
SecGuide/Pol_SecGuide_0100_LdapEnforceChannelBinding

Explanation

Beginning with the Windows 10 and Windows Server v2004 security baseline this setting has been moved to Security Options\Domain controller: LDAP server channel binding token requirements.

Use cases

Requires channel binding for LDAP authentications on domain controllers to counter relay attacks over LDAP over TLS. It goes along with the LDAP signing requirement described in advisory ADV190023.

Test with the "when supported" mode and monitor Directory Service log events before enforcing the strict value, since older clients may fail. Note that this ADMX setting is marked deprecated in the baseline.

Microsoft source: 2020, 2023, and 2024 LDAP channel binding and LDAP signing requirements for Windows (KB4520412)

Registry

HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\NTDS\Parameters
Value name
LdapEnforceChannelBinding
StateValue written
Enablednot defined in the ADMX (see the options below)
Disablednot defined in the ADMX (see the options below)

PowerShell

PowerShell commands that write to the registry what the policy would write. Values in angle brackets (<…>) must be replaced.

The ADMX does not specify the value written when enabled; the GPO editor usually writes REG_DWORD 1 (enabled) / 0 (disabled). The commands below use 1/0 as an assumption.

Writing directly to the registry bypasses Group Policy: if a GPO manages this value, it will be rewritten at the next gpupdate; otherwise the value stays in place (the "tattooing" effect). Prefer a GPO or, locally, LGPO.exe. Run PowerShell as administrator for HKLM. Some policies need a restart or gpupdate /force.

Enable

# Enable: SecGuide/Pol_SecGuide_0100_LdapEnforceChannelBinding
$k = 'HKLM:\System\CurrentControlSet\Services\NTDS\Parameters'
if (-not (Test-Path -Path $k)) { New-Item -Path $k -Force | Out-Null }
# The ADMX does not specify the value written; the GPO editor usually writes REG_DWORD 1 (enabled) / 0 (disabled)
Set-ItemProperty -Path $k -Name 'LdapEnforceChannelBinding' -Value 1 -Type DWord  # assumed value (not defined in the ADMX)
# Configure LdapEnforceChannelBinding
# Possible options:
#   Enabled, always (recommended) = 2
#   Enabled, when supported = 1
#   Disabled = 0
Set-ItemProperty -Path $k -Name 'LdapEnforceChannelBinding' -Value 2 -Type DWord

Disable

# Disable: SecGuide/Pol_SecGuide_0100_LdapEnforceChannelBinding
$k = 'HKLM:\System\CurrentControlSet\Services\NTDS\Parameters'
if (-not (Test-Path -Path $k)) { New-Item -Path $k -Force | Out-Null }
# The ADMX does not specify the value written; the GPO editor usually writes REG_DWORD 1 (enabled) / 0 (disabled)
Set-ItemProperty -Path $k -Name 'LdapEnforceChannelBinding' -Value 0 -Type DWord  # assumed value (not defined in the ADMX)

Revert to "Not configured"

# Revert to "Not configured": SecGuide/Pol_SecGuide_0100_LdapEnforceChannelBinding
$k = 'HKLM:\System\CurrentControlSet\Services\NTDS\Parameters'
Remove-ItemProperty -Path $k -Name 'LdapEnforceChannelBinding' -ErrorAction SilentlyContinue

Options (1)

LabelControlRegistry valueREG typeConstraints / details
Configure LdapEnforceChannelBindingPol_SecGuide_LdapEnforceChannelBindingDrop-down listenumLdapEnforceChannelBindingREG_DWORD
Default choice (UI): #0
LabelValue
Enabled, always (recommended)REG_DWORD = 2
Enabled, when supportedREG_DWORD = 1
DisabledREG_DWORD = 0

Application

Microsoft Security Baseline (MSS, SecGuide) (Microsoft) — November 2026 templates

Official templates downloaded on November 12, 2026.