Open in the explorer

Configure Scenario Execution Level

Configurer le niveau d’exécution des scénarios

Type
Computer
GPO path
Computer Configuration › Policies › Administrative Templates › System › Troubleshooting and Diagnostics › Windows Memory Leak Diagnosis FR: Configuration ordinateur › Stratégies › Modèles d'administration › Système › Dépannage et diagnostics › Diagnostic de fuite de mémoire Windows
Supported on
At least Windows Vista FR: Au minimum Windows Vista
ADMX file
LeakDiagnostic.admx
Internal name
LeakDiagnostic/WdiScenarioExecutionPolicy

Explanation

This policy setting determines whether Diagnostic Policy Service (DPS) diagnoses memory leak problems.

If you enable or do not configure this policy setting, the DPS enables Windows Memory Leak Diagnosis by default.

If you disable this policy setting, the DPS is not able to diagnose memory leak problems.

This policy setting takes effect only under the following conditions:
-- If the diagnostics-wide scenario execution policy is not configured.
-- When the Diagnostic Policy Service is in the running state. When the service is stopped or disabled, diagnostic scenarios are not executed.

Note: The DPS can be configured with the Services snap-in to the Microsoft Management Console.

No operating system restart or service restart is required for this policy to take effect. Changes take effect immediately.

French text from Windows 11 26H2

Ce paramètre de stratégie détermine si le service de stratégie de diagnostic doit diagnostiquer les problèmes de fuite de mémoire.

Si vous désactivez ce paramètre de stratégie ou si vous ne le configurez pas, le service de stratégie de diagnostic active par défaut la fonction de diagnostic de fuite de mémoire Windows.

Si vous désactivez ce paramètre de stratégie, le service de stratégie de diagnostic ne peut pas diagnostiquer les problèmes de fuite de mémoire.

Ce paramètre de stratégie ne prend effet que dans les conditions suivantes :
- La stratégie d’exécution des scénarios de diagnostic n’est pas configurée.
- Le service de stratégie de diagnostic est en cours d’exécution. Lorsque le service est arrêté ou désactivé, les scénarios de diagnostic ne sont pas exécutés.

Remarque : le service de stratégie de diagnostic peut être configuré avec le composant logiciel enfichable Services dans la console MMC (Microsoft Management Console).

Aucun redémarrage du système d’exploitation ou d’un service n’est nécessaire pour rendre ce paramètre de stratégie effectif. Les modifications sont appliquées immédiatement.

Registry

HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\WDI\{eb73b633-3f4e-4ba0-8f60-8f3c6f53168f}
Value name
not defined in the ADMX
StateValue written
Enabled
KeyValueData
SOFTWARE\Policies\Microsoft\Windows\WDI\{eb73b633-3f4e-4ba0-8f60-8f3c6f53168f}ScenarioExecutionEnabledREG_DWORD = 1
SOFTWARE\Policies\Microsoft\Windows\WDI\{eb73b633-3f4e-4ba0-8f60-8f3c6f53168f}EnabledScenarioExecutionLevelREG_DWORD = 2
Disabled
KeyValueData
SOFTWARE\Policies\Microsoft\Windows\WDI\{eb73b633-3f4e-4ba0-8f60-8f3c6f53168f}ScenarioExecutionEnabledREG_DWORD = 0
SOFTWARE\Policies\Microsoft\Windows\WDI\{eb73b633-3f4e-4ba0-8f60-8f3c6f53168f}EnabledScenarioExecutionLevelREG_DWORD = 1

PowerShell

PowerShell commands that write to the registry what the policy would write. Values in angle brackets (<…>) must be replaced.

Writing directly to the registry bypasses Group Policy: if a GPO manages this value, it will be rewritten at the next gpupdate; otherwise the value stays in place (the "tattooing" effect). Prefer a GPO or, locally, LGPO.exe. Run PowerShell as administrator for HKLM. Some policies need a restart or gpupdate /force.

Enable

# Enable: LeakDiagnostic/WdiScenarioExecutionPolicy
$k = 'HKLM:\SOFTWARE\Policies\Microsoft\Windows\WDI\{eb73b633-3f4e-4ba0-8f60-8f3c6f53168f}'
if (-not (Test-Path -Path $k)) { New-Item -Path $k -Force | Out-Null }
Set-ItemProperty -Path $k -Name 'ScenarioExecutionEnabled' -Value 1 -Type DWord
Set-ItemProperty -Path $k -Name 'EnabledScenarioExecutionLevel' -Value 2 -Type DWord

Disable

# Disable: LeakDiagnostic/WdiScenarioExecutionPolicy
$k = 'HKLM:\SOFTWARE\Policies\Microsoft\Windows\WDI\{eb73b633-3f4e-4ba0-8f60-8f3c6f53168f}'
if (-not (Test-Path -Path $k)) { New-Item -Path $k -Force | Out-Null }
Set-ItemProperty -Path $k -Name 'ScenarioExecutionEnabled' -Value 0 -Type DWord
Set-ItemProperty -Path $k -Name 'EnabledScenarioExecutionLevel' -Value 1 -Type DWord

Revert to "Not configured"

# Revert to "Not configured": LeakDiagnostic/WdiScenarioExecutionPolicy
$k = 'HKLM:\SOFTWARE\Policies\Microsoft\Windows\WDI\{eb73b633-3f4e-4ba0-8f60-8f3c6f53168f}'
Remove-ItemProperty -Path $k -Name 'ScenarioExecutionEnabled' -ErrorAction SilentlyContinue
Remove-ItemProperty -Path $k -Name 'EnabledScenarioExecutionLevel' -ErrorAction SilentlyContinue

Availability