Ouvrir dans l'explorateur

Allow JavaScript to use JIT on these sites

Cette stratégie n'a pas de traduction française dans les modèles de l'éditeur ; le texte original est en anglais.

Type
Ordinateur et utilisateur
Chemin GPO
Configuration ordinateur › Stratégies › Modèles d'administration › Microsoft Edge › Paramètres de contenu Configuration utilisateur › Stratégies › Modèles d'administration › Microsoft Edge › Paramètres de contenu EN : Computer Configuration › Policies › Administrative Templates › Microsoft Edge › Content settingsEN : User Configuration › Policies › Administrative Templates › Microsoft Edge › Content settings
Pris en charge sur
Microsoft Edge version 93, Windows 7 or later
Fichier ADMX
msedge.admx
Nom interne
msedge/JavaScriptJitAllowedForSites

Explication

Allows you to set a list of site URL patterns that specify sites that are allowed to run JavaScript with JIT (Just In Time) compiler enabled.

For detailed information on valid site URL patterns, see https://go.microsoft.com/fwlink/?linkid=2095322. Wildcards, *, are allowed.

You can set policy exceptions for specific subdomains and entire sites. For example, a policy set only for subdomain.contoso.com applies to subdomain.contoso.com without affecting contoso.com. In some cases, when a subdomain can't be isolated from its parent site, it may inherit the policy set on the parent site. Exceptions also may not take effect for frames loaded in an existing tab until the site is opened in a new tab. On low-memory Android devices, site-specific exceptions may not be enforced. Instead, sites use the policy from 'DefaultJavaScriptJitSetting' (Control use of JavaScript JIT), if set, or default to the profile's JavaScript JIT setting.

To enforce exceptions, Microsoft Edge may place sites or subdomains with settings that differ from the default in dedicated processes. This behavior can increase memory usage, especially on Android devices or when a wildcard pattern matches many subdomains, because each matching origin may be isolated separately. Isolated subdomains also can't use document.domain to access their parent site.

Note: In version 155 and earlier, policy exceptions were enforced only at the site level (eTLD+1). A policy set only for subdomain.contoso.com didn't take effect, even for subdomain.contoso.com. The policy had to be set on contoso.com to apply to both contoso.com and subdomain.contoso.com.

This policy applies on a frame-by-frame basis and isn't based only on the top-level origin URL. For example, if contoso.com is listed in the 'JavaScriptJitAllowedForSites' (Allow JavaScript to use JIT on these sites) policy, but contoso.com loads a frame that contains fabrikam.com, contoso.com has JavaScript JIT enabled. However, fabrikam.com uses the policy from 'DefaultJavaScriptJitSetting', if set, or defaults to JavaScript JIT enabled. Blocklist entries have higher priority than allowlist entries, and allowlist entries have higher priority than the configured default value.

If you don't configure this policy for a site, the policy from 'DefaultJavaScriptJitSetting' applies to the site, if set. Otherwise, JavaScript JIT is enabled for the site.

Example value:

[*.]example.edu

Registre

HKEY_LOCAL_MACHINE\Software\Policies\Microsoft\Edge
HKEY_CURRENT_USER\Software\Policies\Microsoft\Edge
Nom de la valeur
non défini dans l'ADMX

Valeurs d'activation / désactivation : non défini dans l'ADMX (voir les options ci-dessous).

PowerShell

Commandes PowerShell qui écrivent dans le registre ce que la stratégie écrirait. Les valeurs entre chevrons (<…>) sont à remplacer.

Écrire directement dans le registre contourne la stratégie de groupe : si une GPO gère cette valeur, elle sera réécrite au prochain gpupdate ; sinon la valeur reste en place (effet « tatouage »). Préférez une GPO ou, en local, LGPO.exe. Exécutez PowerShell en administrateur pour HKLM. Certaines stratégies demandent un redémarrage ou gpupdate /force.

Ordinateur (HKLM)

Activer

# Activer : msedge/JavaScriptJitAllowedForSites
$k = 'HKLM:\Software\Policies\Microsoft\Edge\JavaScriptJitAllowedForSites'
if (-not (Test-Path -Path $k)) { New-Item -Path $k -Force | Out-Null }
# Allow JavaScript to use JIT on these sites
# Liste non additive : les valeurs existantes de la clé sont d'abord effacées
if (Test-Path -Path $k) { (Get-Item -Path $k).Property | ForEach-Object { Remove-ItemProperty -Path $k -Name ([WildcardPattern]::Escape($_)) -ErrorAction SilentlyContinue } }
$values = @('<valeur1>', '<valeur2>')  # Remplacez les valeurs par les vôtres
$i = 1
foreach ($v in $values) { Set-ItemProperty -Path $k -Name ('' + $i) -Value $v -Type String; $i++ }

Désactiver

# Désactiver : msedge/JavaScriptJitAllowedForSites
# Aucune valeur n'est écrite à l'état « Désactivé » (rien de défini dans l'ADMX)

Revenir à « Non configuré »

# Revenir à « Non configuré » : msedge/JavaScriptJitAllowedForSites
$k = 'HKLM:\Software\Policies\Microsoft\Edge\JavaScriptJitAllowedForSites'
Remove-Item -Path $k -Recurse -Force -ErrorAction SilentlyContinue

Utilisateur (HKCU)

Activer

Désactiver

Revenir à « Non configuré »

Options (1)

LibelléContrôleValeur de registreType REGContraintes / détails
Allow JavaScript to use JIT on these sitesJavaScriptJitAllowedForSitesDescListe (tableau)listSoftware\Policies\Microsoft\Edge\JavaScriptJitAllowedForSitesValeurs nommées « » + n°REG_SZ (valeurs sous la clé)

Application

Microsoft Edge (+ Edge Update, WebView2) (Microsoft) — modèles de novembre 2026

Modèles officiels téléchargés le 12 novembre 2026.